LOCTITE® 404 - Bottle 10.0/case
Features and Benefits
Available sizes:
Low viscosity, liquid ethyl cyanoacrylate adhesive designed for bonding of plastics and elastomeric materials where very fast fixturing is required.
LOCTITE® 404 is a transparent, colorless to straw colored, low viscosity, liquid ethyl cyanoacrylate adhesive designed for bonding of plastics and elastomeric materials where very fast fixturing is required. It has been qualified to Commercial Item Description A-A-3097 (Note: This is a regional approval).
- Designed for bonding of plastics and elastomeric materials
- Fast fixturing
- Qualified to Commercial Item Description A-A-3097 (This is a regional approval)
Documents and Downloads
Safety Data Sheets and RoHs
- Bottle 10.0/case - IDH 135465
- Bottle 5.0/case - IDH 234044
- Bottle 10.0/case - IDH 234046
LOCTITE® 404, 4 oz Bottle 234044 en-CA
IDH:
234044
EAN:
079340465480
Size Case: Bottle
Quantity: 5.0/case
LOCTITE® 404, 1 lb Bottle 234046 en-CA
IDH:
234046
EAN:
079340465619
Size Case: Bottle
Quantity: 10.0/case
No documents found
Looking for a TDS or SDS in another language?
Technical Information
| Agency approvals / certificates / specifications | Commercial item std. A-A-3097 |
| Application method | Manual |
| Applications | Bonding plastic, Bonding rubber |
| Color | Clear |
| Cure type | Moisture cure |
| Fixture time, Steel | 20.0 sec. |
| Gap fill | 0.15 mm |
| Key characteristics | Viscosity: low viscosity, fixture: very fast fixture |
| Operating temperature | -40.0 - 180.0 °F (-40.0 - 80.0 °C ) |
| Physical form | Liquid |
| Recommended for use with | Elastomer, Plastic, Rubber |
| Shear strength, Mild Steel (grit blasted) | 3500.0 psi (24.0 N/mm² ) |
| Specific gravity, @ 25.0 °C | 1.09 |
| Viscosity | 90.0 mPa·s (cP) |
How to
Step by Step Guide
1. Preparation - Cleaning
It is recommended to use the correct LOCTITE® cleaner for the surface to be bonded (such as LOCTITE® SF 7070) to degrease and clean surfaces prior to applying the adhesive.
2. Preparation - Priming
To improve adhesion on difficult to bond plastic surfaces, apply LOCTITE® SF 770 to the bond area by brushing or dipping. Avoid applying excess primer. Allow the primer to dry.
3. Preparation - Activation
If cure speed is too slow, use activator LOCTITE® SF 7452 (see cure speed vs activator graph in TDS). Apply activator to one bond surface by spray, brush or dipping (not primed surfaces). Allow the activator to dry.
4. Application
Apply adhesive onto one side/part.
5. Assembly
Assemble parts immediately. The parts should be accurately located as the short fixture time leaves little opportunity for adjustment. Bond should be held or clamped until the adhesive has fixtured. Hint: if necessary, excess product can be cured by activator LOCTITE® SF 7452. Spray or drop activator onto excess product.
Equipment
For precise dispensing of small amounts of adhesive, the use of dispensing needles is recommended.
Frequently Asked Questions
Are there any instant adhesive solutions for making replacement, high performance O-rings?
Why does the plastic crack when I use an instant adhesive?
Why is there a white haze on my parts around the bond area?
Do instant adhesives need to be refrigerated?
What health and safety (H&S) precautions do I need to take with this product?
LOCTITE® 404
Low viscosity, liquid ethyl cyanoacrylate adhesive designed for bonding of plastics and elastomeric materials where very fast fixturing is required.