Skip to Content
Henkel Adhesive Technologies
Recent searches

      Henkel Adhesive Technologies
      Loctite Technology Cluster Brand for Product Detail Pages

      Part no. (SKU/IDH):
      135466

      IDH Name:
      LOCTITE® 480, 20 g Bottle

      Instant adhesives

      LOCTITE® 480

      Toughened, low-viscosity adhesive

      A 1-part, rubber toughened, low-viscosity, black adhesive ideal for impact applications.

      Part no. (SKU/IDH):
      135466

      IDH Name:
      LOCTITE® 480, 20 g Bottle
      Part no. (SKU/IDH) 135466
      LOCTITE® 480, 20 g Bottle

      Size Please make your selection 20 g

      All marks used are trademarks and/or registered trademarks of Henkel and its affiliates in the US, Germany, and elsewhere.

      Information

      LOCTITE® 480 is a black, low-viscosity, rubber-toughened instant adhesive designed for close-fitting parts. It has excellent peel, impact and shear strengths and has a fixture time of approximately 90 seconds. It is suitable for use on metals, elastomers and plastics.
      • Toughened, black
      • Low viscosity
      • Excellent peel, impact and sheer strength
      • Easy-to-use

      How to use

        It is recommended to use the correct LOCTITE® cleaner for the surface to be bonded (such as LOCTITE® SF 7070) to degrease and clean surfaces prior to applying the adhesive.

        To improve adhesion on difficult to bond plastic surfaces, apply LOCTITE® SF 770 to the bond area by brushing or dipping. Avoid applying excess primer. Allow the primer to dry.

        If cure speed is too slow, use activator LOCTITE® SF 7452 or LOCTITE® SF 7455 (see cure speed vs activator graph in TDS). Apply activator to one bond surface by spray, brush or dipping (not primed surfaces). Allow the activator to dry.

        Apply adhesive onto one side/part.

        Assemble parts immediately. The parts should be accurately located as the short fixture time leaves little opportunity for adjustment. Bond should be held or clamped until the adhesive has fixtured.Hint: if necessary, excess product can be cured by activator LOCTITE® SF 7452. Spray or drop activator onto excess product.

        For precise dispensing of small amounts of adhesive, the use of dispensing needles is recommended.

      FAQ

        There are several methods to toughen CA adhesives, but the most popular ways are using rubber or anhydride toughening agents. The toughening agents are designed to absorb and distribute impact and stress applied to the adhesive bond line resulting in a tougher bond.

        This is called blooming. This often occurs when there is an excessive amount of product being applied. To avoid blooming, use proper ventilation, less product, lower humidity, use a primer/accelerator, or a low bloom product.

        This is a result of stress cracking. Leaving uncured liquid CA remaining on some plastic substrate (such as polycarbonate, acrylic, and polysulfone) in a stressed condition may cause the formation of cracks in the plastic. Some remedies for avoiding/minimizing stress cracking are closing the bond joint quickly, use reinforced grades of plastic, anneal parts, or speed the cure of the CA with accelerator (or light for light curing CA products only)

        This is a result of stress cracking. Uncured liquid CA remaining on some plastic substrate (such as polycarbonate, acrylic, and polysulfone) in a stressed condition may cause the formation of cracks in the plastic. Some remedies for avoiding/minimizing stress cracking are closing the bond joint quickly, using reinforced grades of plastic, anneal parts, or speeding the cure of the CA with accelerator (or light for light curing CA products only).

        All necessary H&S measures and PPE (personal protection equipment) requirements can be found on the product material safety data sheet, all of which are available via our website.

        Henkel has several products available with varying levels of NSF® approval, amongst others. Please contact the Henkel sales or technical teams with your requirements.

      You might also need

      • Accessories
        LOCTITE SF 770 Primer - 1.75 fl oz (IDH 2759219)

        Adhesive primers

        LOCTITE® SF 770

        Instant adhesive primer for difficult-to-bond materials
        Out of stock

      Recently viewed products
      No data available

      Request a consultation

      Unplanned downtime or lower plant productivity can prevent you from achieving the manufacturing excellence that you are looking for. Consult with our experts to find ways to make your machine more reliable and reduce unplanned downtime to save costs.
      Contact an expert

      Henkel Adhesive Technologies
      Company
      About us
      Locations
      Careers
      News
      Current Customer eShop
      Sustainability
      Help
      FAQs
      Find a TDS
      Find a SDS
      Find a distributor
      Contact us
      Resource center
      Product search
      Technical Library
      Case studies
      White papers
      Webinars
      Brochures
      Social media
      ⓒ 2025 Henkel Corporation. ALL RIGHTS RESERVED
      You are on a United States website